Furnace Forge Co logoFurnace Forge Co

Furnace Repair

Furnace Blowing Cold Air in Boise: Clear Diagnosis, Local Owner

Why a Boise furnace blows cold air: flame sensors, airflow, igniters and duct leaks checked in order.

  • ✓Owner-Operated
  • ✓Locally Owned
  • ✓Based in SW Boise

A furnace that blows cold air is usually shutting its burners off after a few seconds because of a dirty flame sensor, a failing igniter, or an overheating limit switch caused by restricted airflow. Make sure the thermostat fan is set to Auto, not On, and replace a dirty filter. If air is still cold, call (208) 683-7054.

Check this first

  • Thermostat fan setting: On circulates unheated air between cycles.
  • Filter: replace if grey or clogged.
  • Supply registers open and not blocked by furniture.

Causes behind cold air

  • Coated flame sensor: burners light, then shut off within seconds.
  • Cracked igniter: burners never light.
  • Tripped high-limit switch: burners stop while the blower keeps running.
  • Duct leaks in an attic or crawl space cooling the air before it reaches rooms.
  • Weak blower capacitor reducing airflow.

What we check

  1. Thermostat settings and heat call.
  2. Flame sensor and igniter.
  3. Limit switch and rollout sensor.
  4. Blower amperage and filter.
  5. Duct connections for obvious leaks.

Boise's dry winters and cold nights keep furnaces running for long stretches. Source: [NWS Boise climate summary](https://www.weather.gov/boi/climatesummary). If heat fails completely, see furnace not heating.

Technician insight

In Boise 83709 the dry air and fine dust from nearby foothills clog filters and sensors quicker than most homeowners expect, especially in homes with original ductwork from the 1980s and 1990s around Bird Street and the airport corridor.

Cold Air From Registers In South Boise Home

A 83709 homeowner called after the furnace ran continuously yet supplied only cool air. We found a coated flame sensor and restricted filter on a 22-year-old unit. After cleaning the sensor and installing a new filter the furnace resumed normal heating cycles with proper temperature rise at the vents.

Furnace Blowing Cold Air Services We Offer

✓Flame Sensor Cleaning or Replacement

Cleans or replaces a sensor that shuts the gas valve and leaves only cool air.

✓Ignition System Repair

Repairs or replaces igniters that stop burners lighting.

✓Blower and Capacitor Service

Tests motors and capacitors that cut airflow.

✓Filter and Duct Inspection

Replaces clogged filters and checks duct leaks that cool the air.

✓Thermostat Check

Verifies the heat call and fan setting.

Furnace Blowing Cold Air Cost in Boise, ID

Service Typical Range What Affects It
Diagnostic Visit $95–$175 Covers travel within 83709 and full system check; applied to repairs
Flame Sensor Service $120–$220 Includes cleaning or replacement plus retest
Igniter Replacement $180–$320 Part and labor; varies by furnace model age
Blower Capacitor Swap $140–$260 Common fix for weak airflow in older units

Ranges are typical for Boise, ID and confirmed with an exact written quote before any work starts.

How it works

  1. 1

    System check

    Run the furnace through a cycle while checking thermostat settings and listening for short cycling.

  2. 2

    Component diagnostics

    Test the flame sensor, igniter, gas pressure and limit switch.

  3. 3

    Targeted repair

    Clean sensors, replace failed parts or seal duct joints based on findings.

  4. 4

    Verification

    Restart and confirm temperature rise at several registers.

Pricing

The diagnosis comes first; the repair price is explained before work starts.

Furnace Forge Co — Furnace Repair in Boise

Good to know

Furnace Blowing Cold Air — FAQs

Still have questions? We're happy to talk it through.

(208) 683 7054
+ Why is my furnace blowing cold air?
Usually the burners are shutting off because of a dirty flame sensor, a bad igniter or an overheating limit switch.
+ Can the fan setting cause cold air?
Yes. With the fan set to On, the blower runs between heating cycles and pushes room-temperature air.
+ Can a dirty filter make it blow cold air?
Yes. Restricted airflow trips the high-limit switch, which shuts off the burners while the blower runs.
+ Is it a heat exchanger problem?
Rarely the first cause, but a technician inspects it because a cracked exchanger is a safety issue.

Business hours

Need help? Call us now

Call Furnace Forge Co and describe the problem. We provide upfront quotes and workmanship you can inspect on every furnace repair and maintenance job in Boise 83709.

Call now Get help