Furnace Forge Co logoFurnace Forge Co

Furnace Repair

Furnace Ignition Repair in Boise: Clear Diagnosis, Local Owner

Ignition repair for gas furnaces that click, glow or try to light and shut down: igniters, flame sensors and control faults.

  • ✓Owner-Operated
  • ✓Locally Owned
  • ✓Based in SW Boise

A furnace that tries to start three times and locks out usually has a cracked hot-surface igniter, a coated flame sensor or a failing gas valve. Most modern furnaces use a hot-surface igniter and a flame sensor, so this page covers that system. Older standing-pilot units are covered under pilot light problems. Call (208) 683-7054 if your furnace will not light.

Ignition symptoms

  • No glow from the igniter: igniter or control board.
  • Glows, burners light, then shut off in seconds: flame sensor.
  • Repeated retries then lockout: sensor, gas supply or pressure switch.
  • Clicking with no flame: valve or igniter.

What we check first

  1. Error code on the control board LED.
  2. Igniter resistance and visible cracks.
  3. Flame sensor microamp reading.
  4. Gas valve operation and manifold pressure.
  5. Venting and pressure switch.

Why not just reset it

Repeated resets can let unburned gas build up before the burners light. Have the ignition chain tested before cycling the power again. Cold nights and long run times shorten igniter life. Source: [NWS Boise climate summary](https://www.weather.gov/boi/climatesummary). For standing pilots see pilot light problems.

Technician insight

In Boise 83709, the thing that catches most people out with Furnace Ignition Repair is how quickly dust from the dry summer months coats flame sensors in homes built on the west side near the airport, causing lockouts the first week temperatures drop below 25 degrees.

West Boise ranch home short cycling

A 1994 furnace in a single-story home off Maple Grove stopped firing after the first hard freeze. Testing showed the hot surface igniter had high resistance and the flame sensor read below 1 microamp. The igniter and sensor were replaced, wiring was secured, and the furnace completed five consecutive cycles without lockout.

Furnace Ignition Repair Services We Offer

✓Hot-surface Igniter Replacement

Replaces cracked or weak igniters that prevent burner ignition.

✓Flame Sensor Cleaning

Cleans or replaces oxidized sensors that close the gas valve.

✓Gas Valve Testing

Checks valve operation and manifold pressure.

✓Control Board Diagnostics

Reads codes and tests the ignition sequence.

Furnace Ignition Repair Cost in Boise, ID

Service Typical Range What Affects It
Hot Surface Igniter Replacement $225–$350 Price varies by furnace brand and whether access requires panel removal in tight utility rooms.
Flame Sensor Service $150–$275 Includes cleaning; replacement adds cost if sensor is pitted.
Ignition Module Replacement $300–$550 Higher end when board is discontinued and requires wiring adaptation.

Ranges are typical for Boise, ID and confirmed with an exact written quote before any work starts.

How it works

  1. 1

    Read the code

    Check the board LED and note how many ignition attempts occur.

  2. 2

    Test the igniter and sensor

    Measure igniter resistance and flame sensor signal.

  3. 3

    Check gas and venting

    Verify gas pressure, valve operation and pressure switch.

  4. 4

    Repair and verify

    Replace the failed part and run several full cycles.

Pricing

Parts vary by furnace model; the price is explained after the ignition diagnosis and before work starts.

Furnace Forge Co — Furnace Repair in Boise

Good to know

Furnace Ignition Repair — FAQs

Still have questions? We're happy to talk it through.

(208) 683 7054
+ How do I know I need ignition repair?
The furnace tries to start up to three times and shuts down, or the igniter never glows when the thermostat calls for heat.
+ Can a dirty flame sensor stop ignition?
Yes. Oxidation prevents the board from proving flame, so the gas valve closes even though the igniter works.
+ Is it safe to keep resetting a locked-out furnace?
Repeated resets can let unburned gas build up. Have the ignition system checked first.
+ Do you service older furnaces?
Yes, including hot-surface systems on older units. Standing pilots are covered on the pilot light page.

Business hours

Need help? Call us now

Call Furnace Forge Co and describe the problem. We provide upfront quotes and workmanship you can inspect on every furnace repair and maintenance job in Boise 83709.

Call now Get help