Furnace Forge Co logoFurnace Forge Co

Furnace Repair

Furnace Not Heating in Boise: Clear Diagnosis, Local Owner

Diagnosis for a furnace that runs but gives no warm air, from thermostat signal to igniter, sensor, gas and blower.

  • ✓Owner-Operated
  • ✓Locally Owned
  • ✓Based in SW Boise

When a furnace runs but gives no heat, the cause is usually a failed igniter, a dirty flame sensor, a tripped limit switch from restricted airflow, or a gas supply problem. Check the thermostat setting, the filter and the breaker first. If the house is still cold, call (208) 683-7054 and describe what you hear and see.

No-heat symptoms and likely causes

  • Clicking, then silence: igniter or gas valve not opening.
  • Burners light then go out after a few seconds: dirty flame sensor.
  • Blower runs but air is cool: burners not firing or limit switch tripping.
  • Nothing runs: power, door switch or control board.

What we check first

  1. The thermostat signal and 24-volt power at the board.
  2. Igniter or pilot and the flame sensor.
  3. Gas supply and manifold pressure.
  4. Limit switch and airflow, including the filter.
  5. Heat exchanger condition and venting.

Boise conditions that matter

Dry air and cold nights keep furnaces running for long stretches, and winter inversions can hold cold in the valley for days. Source: [NWS Boise climate summary](https://www.weather.gov/boi/climatesummary). Long run times expose weak parts. Related symptoms: furnace blowing cold air and furnace won't turn on.

Technician insight

In Boise 83709, the thing that catches most people out with Furnace Not Heating is restricted return air from dirty filters in homes built before 1990. Those single-story houses near 1219 S Bird St often have undersized filter grilles that starve the blower, tripping the limit switch repeatedly until the furnace locks out.

No Heat After First Freeze

A 1980s ranch off Overland Road called after the furnace ran but produced no warm air once temperatures hit 18 degrees. Inspection showed a cracked igniter and restricted filter. The igniter was replaced and the filter housing cleaned, restoring full heat output within two hours.

Furnace Not Heating Services We Offer

✓Thermostat Signal Diagnostics

Confirms the thermostat is calling for heat and the board is receiving it.

✓Igniter Replacement

Swaps a failed hot-surface igniter that stops the gas valve opening.

✓Limit Switch and Sensor Repair

Finds why a limit switch tripped, not just resets it.

✓Blower Motor and Capacitor Service

Diagnoses motors that run but do not move heated air.

✓Gas Pressure Check

Measures inlet and manifold pressure to restore proper fuel delivery.

Furnace Not Heating Cost in Boise, ID

Service Typical Range What Affects It
Diagnostic Visit $95–$150 Includes basic electrical and gas safety checks; waived if repair is approved same day.
Igniter Replacement $180–$320 Parts and labor; price rises with high-efficiency condensing models.
Blower Motor Service $250–$450 Varies by motor type and whether capacitor or wheel replacement is needed.
Gas Valve Replacement $320–$550 Includes pressure testing; higher for two-stage valves in newer homes.

Ranges are typical for Boise, ID and confirmed with an exact written quote before any work starts.

How it works

  1. 1

    Safety and power check

    Confirm power to the control board and no gas odor before opening the cabinet.

  2. 2

    Thermostat and control testing

    Measure voltage at the board and test the call for heat.

  3. 3

    Component isolation

    Test the igniter, gas valve, sensor and blower to find the failed part.

  4. 4

    Repair and verification

    Replace the part and run a full cycle, checking temperature rise at the registers.

Pricing

Typical costs depend on the part; the price is explained after diagnosis and before repair work starts.

Furnace Forge Co — Furnace Repair in Boise

Good to know

Furnace Not Heating — FAQs

Still have questions? We're happy to talk it through.

(208) 683 7054
+ Why does my furnace run but not heat?
The burners may not be lighting because of a failed igniter, dirty flame sensor or gas issue, or a limit switch may be shutting them off.
+ Can a dirty filter cause no heat?
Yes. Restricted airflow overheats the furnace and trips the limit switch, which shuts the burners off.
+ Is it safe to keep resetting it?
Repeated resets hide the cause. If it keeps failing, have it diagnosed.
+ How do I know if it is the thermostat?
A dead display or no click at the furnace points to the thermostat or power; a technician can test the signal.

Business hours

Need help? Call us now

Call Furnace Forge Co and describe the problem. We provide upfront quotes and workmanship you can inspect on every furnace repair and maintenance job in Boise 83709.

Call now Get help