A gas furnace stops heating most often because of a failed igniter, a dirty flame sensor, a weak gas valve or a tripped limit switch. A technician tests the ignition sequence in order, so the failed part is found instead of guessed. If you smell gas, leave and call the gas utility. For no heat, call (208) 683-7054.
How the ignition chain works
Thermostat call, inducer fan, pressure switch, igniter, gas valve, burners, flame sensor, then blower. If any step fails, the control board stops the sequence and the furnace goes quiet or retries.
What we check first
- Thermostat call and 24-volt power at the board.
- Inducer, pressure switch and venting.
- Igniter and flame sensor.
- Gas valve and manifold pressure.
- Heat exchanger condition.
Safety and efficiency facts
- DOE describes older furnaces at 56 to 70 percent AFUE, mid-efficiency at 80 to 83, and high-efficiency at 90 to 98.5. Source: [US DOE home heating guide](https://www.energy.gov/sites/prod/files/2014/01/f6/homeHeating.pdf).
- EPA advises a yearly professional check of fuel-burning heaters and a CO alarm near sleeping areas. Source: [US EPA](https://www.epa.gov/indoor-air-quality-iaq/carbon-monoxides-impact-indoor-air-quality).
- Boise winters average about 20 inches of snow and bring inversions, so gas furnaces run long hours. Source: [NWS Boise climate summary](https://www.weather.gov/boi/climatesummary).
For electric systems see electric furnace repair. For yearly checks see furnace maintenance.
Technician insight
In Boise 83709 the thing that catches most people out with gas furnace repair is the fine dust from the high-desert soil that packs the secondary heat exchanger on units in crawl spaces off Bird Street. Homeowners change the filter but never pull the blower to clean the exchanger fins, so the furnace overheats and trips limit switches every cold snap.
No Heat Call on a December Morning
A homeowner in 83709 reported the furnace running but no warm air reaching vents. Inspection showed the hot-surface igniter had cracked after years of short cycling from a clogged filter. The igniter was swapped, the heat exchanger was vacuumed, and the system was tested through two full cycles before the house reached temperature.
Gas Furnace Repair Services We Offer
✓Igniter Replacement
Hot-surface igniter swaps that restore reliable starts on older gas furnaces.
✓Gas Valve Repair
Cleaning or replacing valves behind weak flame or delayed ignition.
✓Blower Motor Service
Capacitor checks and motor replacement for weak airflow.
✓Heat Exchanger Inspection
Visual and combustion checks for cracks before gases reach living space.
✓Thermostat Calibration
Replacement and wiring fixes for temperature swings.
Gas Furnace Repair Cost in Boise, ID
| Service | Typical Range | What Affects It |
|---|---|---|
| Diagnostic Visit | $125–$175 | Covers full testing; credited toward repair if work proceeds same day |
| Igniter Replacement | $180–$320 | Parts and labor; varies by furnace model age |
| Gas Valve Replacement | $350–$650 | Includes new valve, labor, and re-testing |
| Blower Motor Replacement | $400–$750 | Depends on motor horsepower and capacitor condition |
Ranges are typical for Boise, ID and confirmed with an exact written quote before any work starts.
How it works
- 1
Safety shutdown and visual check
Turn off gas and power, then inspect venting, wiring and visible components.
- 2
Systematic diagnosis
Control board, igniter, gas valve and blower are tested in sequence with a multimeter.
- 3
Targeted repair
Only the confirmed faulty part is repaired or replaced with matched components.
- 4
Post-repair test
The unit runs a full cycle while flame, temperature rise and exhaust are monitored.
Pricing
Costs depend on the part and furnace model; the price is explained after the diagnosis and before repair work starts.
